Show simple item record

dc.contributor.advisorPalomino Töfflinger, Jan Amaru
dc.contributor.authorPerich Ibáñez, Renzo Alberto
dc.date.accessioned2021-03-31T21:50:28Z
dc.date.available2021-03-31T21:50:28Z
dc.date.created2020
dc.date.issued2021-03-31
dc.identifier.urihttp://hdl.handle.net/20.500.12404/18714
dc.description.abstractThe single-diode model is used to characterize a photovoltaic (PV) solar cell using an equivalent circuit and an equation that depends on five electric parameters. Three analytical methods are applied to extract the five parameters from an Aluminium Back Surface Field (Al-BSF) PV module using 500 experimental current-voltage (I-V) curves measured in the 100-1000W/m2 range. Two of these methods are also applied to four thin-film PV modules, using four experimental I-V curves measured at an irradiance of 1000 W/m2 and air temperature 25℃. While parameter extraction methods have been studied before, this work offers a new perspective by applying the techniques to outdoor PV modules in Lima-Peru and, on the other hand, thin-film technologies located in Jaen-Spain. Results are presented by comparing the measured I-V curve with the ones modelled using the extracted parameters. The Normalized Root Mean Square Error (NRMSE) is calculated to evaluate and compare each extraction method. Values of NRMSE are then grouped by irradiance using a series of boxplots or bar charts to better visualize the success of each extraction method. The results indicate that the method proposed by Phang et al. is very robust, obtaining low values for error across the different irradiances and technologies (median NRMSE of 0.20 % for silicon and 0.50-1.10 % for thin-films). The Blas et al. method obtained low error with the silicon module (median NRMSE of 0.21 %), it was not applied to thin-films in this study. Finally, the Khan et al. method showed greater error than the other two when applied to the Al-BSF and thin-film modules, with noticeably higher error when applied to amorphous silicon modules (median NRMSE of 0.30 % for silicon and 1.77-6.73 % for thin-films).es_ES
dc.language.isoenges_ES
dc.publisherPontificia Universidad Católica del Perúes_ES
dc.rightsinfo:eu-repo/semantics/openAccesses_ES
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/2.5/pe/*
dc.subjectSistemas de energía fotovoltaicaes_ES
dc.subjectDiodoses_ES
dc.subjectPelículas delgadases_ES
dc.titleEstudio y aplicación de métodos analíticos para la extracción de parámetros eléctricos del modelo de un solo diodo para distintas tecnologías de módulos fotovoltaicoses_ES
dc.typeinfo:eu-repo/semantics/bachelorThesises_ES
thesis.degree.nameBachiller en Ciencias con mención en Físicaes_ES
thesis.degree.levelBachilleratoes_ES
thesis.degree.grantorPontificia Universidad Católica del Perú. Facultad de Ciencias e Ingenieríaes_ES
thesis.degree.disciplineCiencias con mención en Físicaes_ES
renati.advisor.dni48866095
renati.advisor.orcidhttps://orcid.org/0000-0002-2076-4046es_ES
renati.author.dni76287271
renati.discipline533056es_ES
renati.levelhttps://purl.org/pe-repo/renati/level#bachilleres_ES
renati.typehttps://purl.org/pe-repo/renati/type#trabajoDeInvestigaciones_ES
dc.publisher.countryPEes_ES
dc.subject.ocdehttp://purl.org/pe-repo/ocde/ford#1.03.00es_ES


Files in this item

Thumbnail
Thumbnail

This item appears in the following Collection(s)

Show simple item record

info:eu-repo/semantics/openAccess
Except where otherwise noted, this item's license is described as info:eu-repo/semantics/openAccess